|
 |
|
 |
| |
|
pneumatic |
hydraulic |
pneumatic |
hydraulic |
pneumatic |
hydraulic |
pneumatic |
hydraulic |
pneumatic |
hydraulic |
hydraulic |
| TD3-60(TD3-60N) |
TD3-80 |
TD5-85 |
TD6-130 |
TD7-130 |
TD8-150 |
TD9-150 |
| Max. drilling capacity(mm) |
Ø6(S45C) |
Ø6(S45C) |
Ø10(S45C) |
Ø16(S45C) |
Ø18(S45C) |
Ø25(S45C) |
Ø35(S45C) |
| Spindle nose taper (mm) |
JT1, JT2,
ER-16 |
JT1, JT2,
ER-16 |
JT6,
ER-20 |
JT6, MT2,
ER-20 |
JT6, MT2,
ER-20 |
MT3A, MT3B, ER-40 |
NT40, NT40A, FB30 |
| Max
travel of spindle (mm) |
60 |
80 |
85 |
130 |
130 |
150 |
150 |
| Cutting feed stroke (mm) |
25、50 |
60 |
25、50 |
80 |
25、50 |
85 |
25、50 |
130 |
25、50 |
130 |
150 |
150 |
| Spindle speed (rpm) |
12000 |
10500 |
6000 |
3200 |
3200 |
1500 |
1250 |
| Cylinder dia |
Forward 12.6cm2
Backward 7.1cm2 |
Forward 12.6cm2
Backward 7.1cm2 |
Forward 21.6cm2
Backward 11.6cm2 |
Forward 43.2cm2
Backward 30.6cm2 |
Forward 43.2cm2
Backward 30.6cm2 |
Forward
71.2cm2
Backward
44.8cm2 |
Forward
71.2cm2
Backward
31.4cm2 |
| Motor rating |
2 Phases, 2/4 Poles 220/380w |
|
| Working pressure (kg) |
5 |
10 |
5 |
10 |
5 |
20-25 |
5 |
20-25 |
5 |
20-25 |
20-25 |
20-25 |
| Net weight |
20 (kg) |
22 (kg) |
42 (kg) |
32 (kg) |
32 (kg) |
55 (kg) |
65 (kg) |
| The above air-hydraulic machines equipped with a 25mm long stabilizer. |
|
|
Characteristics:
* These units save energy because of using both electric driving electric and air feeding. (Cutting feed speed is controlled hydraulically.)
* It is easy to set full stroke and rapid stroke by adjusting knob.
* The six different spindle speeds are available by simply replacing the interchangeable pulley.
* Motor is protected by built-in thermostat.
* Unique design of the independent throttle rod system eliminates any bending moment to the quill.
* These unites contain the oil reservoir inside, which minimizes the oil supplies.
* Aluminum die casting housing give the great rigidity and light weight compact design.
| |
AF1-112(AF1-112S) |
AF2-126(AF2-126S) |
| Max. drilling capacity |
Ø8 |
Ø9 |
| Spindle nose taper |
J.T.1 |
J.T.6 |
| Spindle Whole
Stroke: mm |
80 |
120 |
| Drilling Feed
Stroke: Max. mm |
50 |
90 |
| Requested Rapid
Feed Stroke : Min. mm |
30 |
| Spindle speed 60Hz(rpm) |
6000, 4000, 2700, 1800, 1200, 800 |
5000, 3550, 2500, 1800, 1250, 900 |
| Drilling Feed
Rate: mm/sec |
0.4～ 20 |
| Thrust Power
(As 5 Kgf /cm2G air Pressure) |
100(kgf) |
150(kgf) |
| Working air pressure (kg) |
5 kgf/cm2G |
| Drive Motor
Power |
3 Phases, 2 Poles 200W |
3 Phases, 2 Poles 375W |
| Net weight |
15(kgf) |
31(kgf) |
|
|
|
|
|
|